Tecjet technical service
Touch Panal menu
Main menu function description
1.1 Station POS: Standby, car in the position of the ink station;
Press the left and right keys to move the car position, confirm the key to
determine, the return key to cancel;
1.2 Wipe POS: The position of the car after scraping the sprinkler head;
Press the left and right keys to move the car position, confirm the key to
determine, the return key to cancel;
1.3 Wiper POS: Set the position of the scraper when the nozzle is scraped;
Press the left and right keys to move the car position, press the up and
down keys to move the scraper position, confirm the key to determine,
the return key to cancel;
1.4 Spit Height: The height of the flash ink station;
Up and down key lifting ink station, confirm the key to determine,
return key to cancel;
1.5 Print Spit Switch:Whether to turn on printing flash;
Press up and down key to select on/off, confirm key to confirm,
return key to cancel;
1.6 Blank Spit Switch:Whether to start jumping white flash jet;
Press up and down key to select on/off, confirm key to confirm,
return key to cancel;
1.7 Spit POS: The position of the car during flash spraying;
Press the left and right keys to move the car position, confirm the key to
determine, the return key to cancel;
1.8 Spit Dots:Flash spray amount
1.9 Waste ink Set:Clean and pump waste ink, set the ink pump pumping time intensity
2.0 Nozzle Test:Nozzle Check
Press the “confirm” button to confirm, the car out of the ink station to
print the test bar, and then back to the warehouse;
2.1 Clean Nozzle:The equipment automatically carries out the actions such as ink
extraction, nozzle scraping, flash spraying, etc.;
Press the confirm key to determine, the ink station began to head ink,
scraper, back to the origin flash jet, finally head;
2.2 Manual Pump:Carry out manual inking;
Press the confirmation key to confirm, ink station head to draw ink,
press the confirmation key to pause, press the return key to cancel;
2.3 Wipe Nozzle:The device wipes the nozzle;
Press the “confirm” button to confirm that the car will be moved to the
position of the scraping nozzle on the left.
2.4 Flush:Artificial flash spraying;
Press the “ok” button to confirm that the nozzle is flashing at the origin, and
press the “back” button to cancel;
2.5 Cap Head:Equipment capping head;
Press the confirm button to confirm, the ink station up to the ink cartridge
stick to the nozzle;
Description of the standby interface menu
1.1.1: “direction”: Select either One Way or Two Way
1.1.2: “velocity”: Print speed, you can select Standard or Height
1.1.3: “blow head”: Select Head print to select Left, Right, or Double
1.2: “induced draft”: The wind force of the platform fan can be set at grade 1-16
1.3: “contrast ratio”: Panel screen contrast, the higher the contrast, the more obvious the contrast
1.4: “Automatic maintenance”: The time interval when the machine automatically performs maintenance on standby
1.5: “device address”: The printer’s IP address, select the default or custom address
1.6: “Empty paper alarm”: Check the use of materials; alarm when opened
1.7: “Heating Settings”: Select Open or Off
1.8.1: “The origin of ink station”: Where the car is located on standby
1.8.2: “Flash spray position”: Position of the car before printing and during ink flushing
1.8.3: “Scratch position”: Position of the nozzle when scraping
1.8.4: “Scratch positioning”: Position where the motor blade is removed when scraping
1.8.5: “Scratch height”: The height of the blade when scraping
1.8.6: “Ink station height”: The rising height of the ink station can save the head height and flash spray height
6.1: “Nozzle test”: Print the test bar to facilitate viewing the nozzle status
6.2: “self-cleaning”: Do ink extraction, scraping, flash spray, head sealing and other actions
6.3: “Manual cleaning”: Only ink extraction is carried out
6.4: “Scratch your mouth”: Move the car out, scratch and wash the spray head
6.5: “Chong ink”: The nozzle will flash out
6.6: “capped end”: The ink cartridge is closed with the nozzle surface
Press down up + down + left +right and turn printer on to enter the debug menu
Debug Menu function description
3.1 station: Type of equipment ink station;
up and down key to select the type, press the confirm key to save;
3.2 wiper: Set the device scraper type;
select the type by the up and down key, and press the confirm key to save;
3.3 Print width: Set the print width of the device;
add or subtract values by the up and down keys, and press the confirm key to save;
3.4 Raster type: Set the device grating type;
select the type by the up and down keys, and press the confirm key to save;
3.5 Car motor:Set the motor type of the car;
select the type by the up and down key, and press the confirm key to save;
3.6 Wiper direction: Set the scraper type;
select the type by the up and down key, and press the confirm key to save;
3.7 Paper direction:Set the paper turning direction;
select the direction by the up and down keys, and press the confirm key to save;
3.8 Car direction:Set the steering of the car;
select the direction by the up and down keys, and press the confirm key to save;
3.9 Accelerate distance:Set the trolley movement distance;
increase/decrease the distance by the up and down keys, and press the confirm key to save;
4.0 Paper speed:Set the speed of paper walking;
add or subtract values by the up and down keys, and press the confirm key to save;
4.1 LCD type: Set the type of the display;
set the type by the up and down keys, and press the ok key to save;
4.2 Cap speed:Set the lifting speed of ink station;
increase/decrease the speed by the up and down keys, and press the confirm key to save;
4.3 Wiper speed:Set the moving speed of the scraper;
increase/decrease the speed by the up and down keys, and press the confirm key to save;
4.4 Print paper speed:The paper walking speed of printing is the percentage of the paper walking speed;
such as paper walking speed 90, paper walking speed 20, paper walking speed 90×20%=18. Adjustable range of 10-100;
4.5 Life test:Test card aging;
Press the “confirm” button to confirm that the car moves around the platform to simulate printing and test the durability of the board card;
4.6 Out test: Test whether the output of motherboard port is normal;
Select the corresponding port by the up and down keys, press the ok key, and the port will light up when “Off” is displayed, while the port will not light up when “ON” is displayed.
4.7 In test:Test whether the main board sensor is normal;
Select the sensor port by the up and down keys, and display “OUT” when blocking the sensor, and “IN” when not blocking the sensor;
4.8 Motor test: Test whether the motor works normally;
Select the corresponding port by the up and down keys, press the confirm key and observe whether the corresponding motor is working;
4.9 Car pos:Test whether the grating works normally;
Move the trolley, press the confirm button, the value increases when moving to the left, and decreases when moving to the right;
5.0 SDR test:Internal memory SDR chip testing
5.1 BUS test:Bus detection
5.2 Spit test:Test flash spray;
press the confirm button, spray spray nozzle;
5.3 Ms note:equipment information
5.4 485A:External 485 communication detection
Press down up + down + left +right and turn printer on to enter the debug menu
Engineer mode menu description
1 Ink station: Select lifting type with motor, select CAP type without motor
2 Scraper: Select motor type with motor, without motor
3 Print width: the maximum width available to print
5 Car motor: servo motor selection servo, DC motor selection DC
6 Paper motor: servo motor selection servo, step motor selection step
7 UV interface: can select Open or Off
8 ScrSteering: Select Forward or Reverse
9 Turn to Paper: Select Forward or Reverse
12 Paper walk speed: Set the paper walk fast and slow, the larger the value, the faster the paper walk
14 Automatic cleaning: standby cleaning way, choose “automatic cleaning” or “flash spray”
15 Scraper speed: set the blade motion fast, the larger the value, the faster the movement
16 Ink station speed: set the slow movement of the ink station, the larger the value, the faster the movement
17 Wift width: When you set the wiper width, the larger the value, the larger the scraping area
18 Cleaning setting (manifested in automatic cleaning):
short draw (short ink time);
short draw (short time of ink);
short draw (short ink);
long draw (long ink time);
long draw (long ink time);
long draw (long ink);
ink maintenance (how long ink maintenance)
Flash frequency (number of nozzle) Flash
frequency (slow flash)
Remove ink (waste time),
drain ink close (how long stop)
Number of residual ink draws (how many times draw)
Press on up + right + exit and power on to enter the debug menu